LG WM3050CW Pump Hose Replacement

LGLG WM3050CWModerate⏱ 1 - 2 hours

Инструкция на английском (оригинал iFixit). Непонятные термины — в разделе «Основы → Словарь».

Use this guide to replace the pump hose in your LG WM3050CW Washing Machine. The pump hose connects the tub to the drain pump. It's not the drain hose, which drains the wastewater out of the washer. The metal ring holding the rubber boot can be difficult to reinstall. You can buy this tool to make the reinstallation easier, or ask additional people to help.

Сначала выполнить:Do these first:

🧰 Tools

Slip Joint Pliers
Phillips #2 Screwdriver
Flathead 4 mm Screwdriver
Needle Nose Pliers
7 mm Nutdriver

ШагиSteps

Step 1

Before you begin your repair, perform the following:
Turn off the main water supply
Unplug your washer
Disconnect all water connections at the rear of your washer

Unfasten the top panel

Use a Phillips driver to remove the two bottom 16.5 mm-long screws securing the top panel brackets.

Remove the top panel

Slide the top panel 1-2 inches towards the rear of the device to disconnect its clips.

Step 4

Tilt the top panel upward to completely disconnect it from the chassis.
Remove the top panel.

Remove the detergent drawer

Pull the detergent drawer away from the chassis as far as it will go.

Step 6

Press down on the "Push" button to disengage the clips securing the detergent drawer.
Pull the drawer out of its slot on the chassis and remove it.

Disconnect the control panel

Disconnect the three harness connectors for the control panel.
Always grip cables by their connectors and not the wires themselves.

Unfasten the control panel

Use a Phillips driver to remove the 16.4 mm-long screw securing the control panel.

Unfasten the detergent dispenser

Use a Phillips driver to remove the two 26.3 mm‑long screws securing the detergent dispenser.

Unclip the control panel

Insert a flathead screwdriver between the chassis and the top left corner of the control panel.
Twist the screwdriver to release the clips securing the control panel.
Repeat this procedure for the remaining clips along the control panel.

Remove the control panel

Lift the control panel upward to completely separate it from the chassis.
Pull the control panel away from the chassis, making sure to thread the cables through its slot in the chassis.
Remove the control panel.

Open the door

Open the front door completely.

Remove the boot ring

Use needle nose pliers to grip the spring end of the metal ring at the bottom of the rubber boot.
Pull the ring away from the chassis to separate it from the boot.

Step 14

Use your hand to completely pull the ring off the boot.
During reassembly, perform the following:
Insert one end of the ring into its groove along the boot's perimeter.
Use pliers to slowly stretch the ring around the boot's perimeter until it's completely nested in its groove.
This procedure will take significant force.

Disconnect the boot

Use your fingers to pull the boot off its lip on the front panel.

Step 16

Work your fingers around the boot until its completely separated from the panel.

Remove the filter panel

Open the filter panel at the bottom left of the front panel.
Twist the filter panel upward to unclip it from the front panel.

Unfasten the filter trim

Use a Phillips driver to remove the two 12.8 mm‑long screws securing the filter trim.

Remove the filter trim

Pull the filter trim straight off the front panel to remove it.

Unfasten the lower front panel

Use a Phillips driver to remove the 12.8 mm-long screw securing the lower front panel.

Unfasten the door latch

Use a Phillips driver to remove the two 16 mm‑long screws securing the door latch.

Remove the door latch

Pull the door latch through its slot in the chassis and let it hang on its wire.

Unfasten the front panel

Hold the front panel against the chassis while performing this step to prevent it from falling.
Use a Phillips driver, or a 7 mm nut driver, to remove the six 15 mm‑long screws securing the front panel.

Remove the front panel

Lift the front panel upward to separate it from its clips on the bottom of the chassis.
Pull the front panel away from the chassis to completely separate the front panel.

Step 25

Remove the front panel.

Disconnect the tub to pump hose

Use slip joint pliers to pinch the tub to pump hose clamp and pull it away from the assembly.
Pull the hose straight off the assembly to disconnect it.

Unfasten the rear panel

Use a Phillips driver to remove the four 10.7 mm‑long screws securing the rear panel.

Remove the rear panel

Lift the rear panel upward to release its bottom clips.
Pull the rear panel away from the chassis to release the remaining clips.

Step 29

Remove the rear panel.

Disconnect the air dome

Pull the air dome hose straight up to disconnect it.

Unfasten the air dome

Use a Phillips driver to remove the two 16.5 mm‑long screws securing the air dome.

Step 32

Use slip joint pliers to pinch the air dome hose clamp and pull it over the dome itself.

Remove the air dome

Pull the air dome straight off its hose to remove it.
During reassembly, make sure the air dome nub is aligned properly with its slot in the hose.

Loosen the pump hose

Use a Phillips driver to loosen the pump hose from the drum enough to disconnect it.

Disconnect the pump hose

Pull the pump hose straight off the drum to disconnect it.

Remove the pump hose

Remove the pump hose.
During reassembly, use liquid laundry detergent to lubricate the hose around its tub connection.

To reassemble your device, follow these instructions in reverse order. Take your e-waste to an R2 or e-Stewards certified recycler. Repair didn’t go as planned? Ask our Answers community for help.

«LG WM3050CW Pump Hose Replacement» — автор Bill Gilbert, iFixit, лицензия CC BY-NC-SA 3.0. Показано без изменений. Открыть оригинал и комментарии →