Hotpoint Aquarius Tumble Dryer Condenser Unit Cleaning

HotpointHotpoint DryerModerate⏱ 20 - 30 minutes

Инструкция на английском (оригинал iFixit). Непонятные термины — в разделе «Основы → Словарь».

Use this guide to remove, clean, and reinstall the condenser unit in a Hotpoint Aquarius Tumble Dryer TCHL73. The condenser unit, also called the condenser or condensing unit, helps remove moisture during drying. Lint, dust, and fibers can block airflow and cause poor drying performance or a Clean Condenser warning. Clean it at least once a month for maximum efficiency, especially if the dryer is used often. Other Hotpoint and Indesit condenser dryers may have minor differences.

🧰 Tools

Scrubbing Sponge
Shop Towels or Rags
Wet Dry Vacuum
Plastic Scraper
Garden Hose

ШагиSteps

Prepare the dryer safely

Turn off the dryer at the wall switch and unplug it from the power supply.
Let the dryer cool if it was used recently, because the condenser area can hold warmth and water.
Clean the condenser unit at least once a month, especially if the dryer is used often.
The dryer may show a Clean Condenser light when the condenser needs attention.

Remove the condenser unit

Pull the lower front panel outward to access the condenser unit at the bottom of the dryer.
Release the three retaining clips holding the condenser unit in place.
Slide the condenser unit straight out toward you.
Keep a sponge or old rag under the opening because a little water may drain from the unit.
Expect dust, fibers, and dirt on the condenser if drying performance has dropped.

Clean the condenser compartment

Use a cloth to wipe dust and dirt from the compartment the condenser came from.
If the compartment is dry, use a wet/dry vacuum to remove loose dust.
Don't use a standard wet/dry vacuum on wet debris; use a wet and dry vac for moisture.
Clean the compartment as thoroughly as possible before refitting the condenser unit.

Remove dry debris from the condenser

Inspect the front and rear of the condenser for a film of dust, lint, and fibers.
Remove as much loose debris as possible before washing the condenser.
This keeps large clumps of lint from going down the drain.
Use an knife as a scraper only where your fingers can't reach.
Keep the blade away from your hands and the condenser fins.
Turn the condenser around and clean the rear side too.
Use a small hand vacuum or wet and dry vac to pull out loose fibers if available.
Clean until the airflow openings look clear and free of packed lint.

Rinse the condenser

Move the condenser to a shower, bath, or sink with a shower head.
Use a garden hose if you prefer to clean the condenser outdoors.
Keep the drain plug in while washing so you can remove lint before it enters the drain.
Set the shower head to its highest spray setting.
Spray through the condenser from different directions until trapped dirt and fibers wash out.
Shake the condenser during rinsing to loosen trapped debris.
Scoop out lint and debris from the bath or sink before removing the drain plug.

Dry the condenser

Leave the condenser to dry for a while after rinsing.
The condenser may dry quickly in warm summer weather.
Use a tea towel to dry the condenser as much as you can if it doesn't dry quickly.
Make sure no loose clumps remain on the outside or in the openings before reinstalling it.
Clean the bath or sink water before draining it so lint doesn't enter the drain.

Reinstall the condenser unit

Hold the condenser with the arrows facing the correct way up.
Insert the condenser at a slight angle and slide it into place.
Don't force the condenser, because it should slide in easily when aligned.
Push the condenser all the way home until it is fully seated.
Move the three clips up to lock the condenser in place.
Close the lower front panel.

Restore power and test the dryer

Plug the dryer back into the power supply and switch it on at the wall.
Load damp clothes and start a drying cycle.
Check drying performance after cleaning the condenser.
Clothes should dry better if the condenser was clogged with lint and fibers.

Maintain drying performance

Clean the lint filter at the front of the drum every time you use the tumble dryer.
A blocked lint filter fills with fluff and fibers and can reduce drying performance.
Clean the condenser at least once a month if the dryer is used frequently.
If clothes stop drying well, clean the condenser and check the condenser compartment for dust again.
After removing dry clothes, spin the drum by hand and check for small items like handkerchiefs.

The condenser unit is clean and reinstalled. Keep the condenser clear monthly, clean the lint filter every drying cycle, and recheck the condenser area if drying performance drops. Repair didn't go as planned? Ask our Answers community for help.

«Hotpoint Aquarius Tumble Dryer Condenser Unit Cleaning» — автор eCuration, iFixit, лицензия CC BY-NC-SA 3.0. Показано без изменений. Открыть оригинал и комментарии →