How to Troubleshoot an Amana Electric Dryer That Won't Heat

AmanaAmana DryerModerate⏱ 45 minutes - 2 hours

Инструкция на английском (оригинал iFixit). Непонятные термины — в разделе «Основы → Словарь».

If an Amana electric dryer runs but doesn’t heat (or takes multiple cycles to dry), the problem is often a failed heater circuit part or a restricted vent that overheated the dryer. This guide shows how to confirm proper 240 V power, open the heater section on common Whirlpool-made designs, test heat components with a multimeter, replace failed parts, and clean lint buildup to help prevent repeat failures.

🧰 Tools

Multimeter
6-in-1 Screwdriver
Putty Knife
Drill
Safety Glasses
Work Gloves

⚙️ Parts

Heating element assembly
High limit cutoff
High limit thermostat
Cycling thermostat
Timer

ШагиSteps

Confirm the dryer style and follow basic safety rules

Confirm the dryer is a Whirlpool-made style by checking that the lint door is on the top panel and the lint screen housing matches the common Whirlpool/Amana layout.
WARNING: Electric dryers use 240 V, which can kill you, so don’t open panels or touch wiring until power is unplugged, except during the controlled voltage test.
Let the dryer cool and wear safety glasses and cut-resistant gloves to reduce burn and sharp-edge risks.

Gather tools for diagnosis and disassembly

Gather a 6-in-1 screwdriver with 1/4 inch and 5/16 inch nut driver sizes, a multimeter, and a putty knife.
Use a drill with a nut driver bit if you want to speed up removing screws.

Check for correct voltage at the terminal block

Keep the dryer plugged in and set the multimeter to AC volts for this test.
Touch one probe to neutral and the other probe to the first hot leg to confirm about 120 V.
Touch one probe to neutral and the other probe to the second hot leg to confirm about 120 V.
Touch one probe to each hot leg to confirm about 240 V across the two legs.
Diagram: L1–N ≈ 120 V, L2–N ≈ 120 V, and L1–L2 ≈ 240 V.
If the L1–L2 reading is much less than 200 V, focus on the house power, breaker reset, outlet, or power cord because dryer component tests won’t be meaningful.
Unplug the dryer after the voltage test.

Remove the rear panel to access the heater system

Use a 1/4 inch or 5/16 inch nut driver to remove about eight screws securing the rear panel.
Remove the rear panel to expose the heating system and its sensors.

Identify the heat system components

Locate the heating element canister, the thermostats, and the high-limit cutoff in the heater circuit area.
Pay close attention to the part names and locations so you can order the correct replacement if a test fails.

Set up the multimeter and avoid false readings

Set the multimeter to continuity mode, or use resistance mode if your meter doesn’t have a continuity buzzer.
Take a photo of the wiring before removing connectors so you can reinstall them correctly.
Pull at least one spade connector off the part you’re testing to prevent backfeeding through the wiring and getting a false “good” reading.

Test the thermostat for continuity

Disconnect at least one wire from the thermostat, then touch a probe to each thermostat terminal.
If the meter shows continuity, the thermostat is good.
If the meter shows an open loop (often shown as OL), the thermostat is bad and should be replaced.

Test the heating element for continuity, resistance, and shorts to ground

Remove the spade connectors from the heating element terminals and test the element for continuity.
Switch to resistance and confirm the element reads about 10 Ω, which may take a few seconds to settle on the meter.
Test for a ground fault by touching one probe to an element terminal and the other probe to the metal canister housing.
If you get continuity to the canister, the element is grounded out and the heater canister assembly needs replaced.

Test the cycling thermostat terminals

Test the cycling thermostat’s two terminals with the red wires for continuity because they control the primary heat function.
If those red-wire terminals have continuity, the primary cycling contacts are good.
Test the cycling thermostat’s purple-wire terminals with resistance mode because they control delicate or lower heat settings.
A typical acceptable resistance range is about 3.6 kΩ to 7.2 kΩ, and values far outside that range can cause incorrect heat settings.

Test the high-limit cutoff and clean airflow restrictions

Test the high-limit cutoff, sometimes called the thermal fuse, for continuity after removing at least one connector.
If the high-limit cutoff is open, replace it, and strongly consider replacing the nearby heater thermostat as a matching set.
Inspect for excessive lint buildup in the blower housing and in the vent pipe that exits the home.
Clean any lint restrictions you find because poor airflow can overheat the dryer and trip the high-limit device.

Access and test the timer if all heater parts test good

Unplug the dryer if it isn’t already unplugged.
Insert a putty knife into the seam between the chassis and the console on one far side, then press in firmly to release the spring clip.
Release the spring clip on the other side, then roll the top forward to lift the console off for timer access.
Remove the left wiring harness connection and leave the right harness in place.
Set the timer to a high heat setting and check the three specified timer contacts for continuity.
If any of the three timer checks don’t show continuity, the timer contacts are burnt and the timer is bad.
If the timer tests good, look for loose wire connections, and be aware some models may use additional modules like a heat relay or a belt switch.

Reassemble and verify operation

Reconnect all spade terminals and harnesses exactly as shown in your reference photo.
Reinstall the console and rear panel, then secure all screws.
Plug the dryer in and run a high heat cycle to confirm the drum heats and airflow is strong at the outside vent.

If the dryer heats after replacing a failed sensor or element, keep it reliable by cleaning the lint screen every load and keeping the entire vent path clear to prevent overheating. If power is correct and all heater components and the timer test good, a wiring issue or model-specific control part may be interrupting heat. Repair didn't go as planned? Ask our Answers community for help.

«How to Troubleshoot an Amana Electric Dryer That Won't Heat» — автор Ben Schlichter, iFixit, лицензия CC BY-NC-SA 3.0. Показано без изменений. Открыть оригинал и комментарии →