How to Troubleshoot a Maytag Dryer That Won't Heat

MaytagMaytag DryerModerate⏱ 1 - 2 hours

Инструкция на английском (оригинал iFixit). Непонятные термины — в разделе «Основы → Словарь».

If a Maytag dryer runs but doesn’t heat, the heating element isn’t the only possible failure point. This guide shows a methodical way to access the rear of a Maytag dryer with a front lint filter, test the heating circuit parts with a multimeter, check the timer heat contacts, and verify incoming power so you can pinpoint what actually failed before replacing parts.

🧰 Tools

1/4 inch hex-head screwdriver
Multimeter
Precision Needle-nose Pliers
Putty Knife
Heat Gun
Work Gloves

⚙️ Parts

Heating Element
Thermal cutoff
High-limit thermostat
Cycling thermostat
Dryer timer
Power cord
Terminal block
wire connector

ШагиSteps

Confirm the dryer style and make it safe

Confirm the dryer has a lint filter at the front, because other Maytag designs can be laid out differently.
Unplug the dryer before opening any panels or touching wiring.
Let the dryer cool down before working near the heater housing.

Remove the rear casing

Use a 1/4 inch hex-head screwdriver to remove the screws securing the rear casing.
Expect nine to 11 screws on many models, but the exact count can vary.
Pull the rear casing straight off and set it aside with the screws for reassembly.

Locate the heating and airflow components

Locate the heater system on the right side, including the thermal cutoff or high-temp thermostat, and the heating element near the bottom.
Locate the blower housing on the left side with the cycling or operating thermostat that regulates heat during normal operation.
Note that thermostat mounting can vary by model, but the testing method is the same.

Test the heating element resistance

Remove one spade connector from the heating element to avoid false readings.
Use pliers to pull the spade connector off if it’s too tight to remove by hand.
Set a multimeter to ohms or continuity and measure across the two element terminals.
A good heating element typically reads 9–10 Ω, while a wildly higher value or no reading suggests the element is bad.
Optionally test the element and heater-side thermostat together by measuring between the thermostat terminals and the element terminal.

Check the heating element for a dangerous ground fault

Set the multimeter to continuity and touch one probe to an element spade terminal and the other probe to the element’s metal casing.
If the meter beeps or shows a reading, the heater is grounded to the cabinet and must be replaced.
A grounded heater can still produce some heat while damaging the dryer and creating a serious hazard.

Inspect wiring and repair burnt connections

Inspect wire terminals and spade connectors for burn marks or melted discoloration.
Treat burnt connectors and damaged wire as likely no-heat culprits, not just cosmetic damage.
Cut off any blackened or damaged wire and splice in a repair using a heavy-gauge splicing connector and a wire nut.

Test the thermal cutoff or high-temp thermostat

Remove one wire from the thermal cutoff or high-temp thermostat before testing it.
Set the multimeter to continuity or ohms and measure across the thermal cutoff terminals.
A good cutoff shows continuity or near 0.0 Ω, while no continuity means it’s open and will prevent any heat.
If this part is open, check for underlying airflow problems like lint buildup or a restricted vent.
Replace a failed thermal cutoff with a matching thermostat as a pair to reduce repeat failures.

Test the cycling or operating thermostat

Remove one red wire from the cycling or operating thermostat for testing.
Test between the thermostat spade and the other spade of the matching red wire for continuity or near-zero resistance.
If the meter shows OL, the circuit is open and the thermostat isn’t passing power.
Remove one of the purple wires on the smaller prongs and measure resistance on the small terminals in ohms mode.
A typical reading is 5,000–10,000 Ω, and a value far out of that range can cause low-heat setting problems.

Optionally heat-test a thermostat that seems to test good

Suspect the cycling thermostat if thermal cutoffs keep blowing even though the thermostat shows continuity at room temperature.
Set the multimeter to continuity or ohms, then apply heat to the thermostat with a hot air gun while watching the meter.
A good thermostat should open at about 155 °F and the meter should switch to OL or open line.
If it keeps passing electricity well beyond 155 °F, replace it because it can overheat the dryer and blow other safety devices.
Use heat tools carefully to avoid burns, melted plastic, or scorched wiring.

Access and test the timer heat contacts

Use a 1/4 inch hex-head screwdriver to remove the screws holding the metal console backing.
Use a putty knife between the console and the top to depress the hidden spring and pivot the console up.
Disconnect the wire harness on the timer for testing.
Find the four labeled connectors A, B, C, and H, then focus testing on A to B and A to C.
Set the timer to a high-heat segment (not cool down), then test A–B and A–C for continuity or resistance.
If you get no continuity or resistance on these pairs, the timer is bad and needs replacement.
Turn the dial clockwise only to avoid damaging the timer gearing and contacts.

Inspect the terminal block and verify incoming voltage

Unplug the dryer, remove the terminal block cover, and inspect the power cord and terminal block for visible damage.
Replace the damaged cord or terminal block immediately if you see burnt or melted areas.
Plug the dryer in only for voltage testing, set the multimeter to AC voltage, and avoid touching any bare metal parts.
Measure middle-to-left and middle-to-right, and expect about 120 V on each side.
Measure left-to-right and expect a total of 208–240 V.
If the left-to-right voltage is below 208 V, troubleshoot the breaker, cord, or outlet before replacing dryer parts.
Cycle the breaker fully off, then fully on, if the voltage readings are abnormal.

Reassemble and do a final heat test

Reconnect all wires and harnesses you removed during testing.
Seat the console by inserting the rear hooks, rocking the console down, and letting the spring clips snap into place.
Reinstall the console backing and its screws.
Reinstall the rear casing and all its screws.
Plug the dryer in and run a high-heat cycle to confirm the dryer heats properly.

A successful dryer heat repair should restore normal heat at the element and thermostat checks, and the dryer should run a high-heat cycle without tripping a safety cutoff. If the dryer still won’t heat, recheck airflow, the thermal cutoff, and the timer or wiring tests. Repair didn't go as planned? Ask our Answers community for help.

«How to Troubleshoot a Maytag Dryer That Won't Heat» — автор Ben Schlichter, iFixit, лицензия CC BY-NC-SA 3.0. Показано без изменений. Открыть оригинал и комментарии →