How to Troubleshoot a GE Front Load Washer Stopping Mid Cycle and Not Spinning
GEGE Washing MachineModerate⏱ 1 - 2 hours
Инструкция на английском (оригинал iFixit). Непонятные термины — в разделе «Основы → Словарь».
If your GE front load washer halts during a cycle or fails to spin, use this guide to diagnose the error codes, run forced spin tests, and replace the inverter board or other components if needed.
🧰 Tools
- 6-in-1 Screwdriver
- Digital Multimeter
- 14 mm socket
- Door Boot Spring Tool
- Needle Nose Pliers
⚙️ Parts
- GE Inverter Board FL Washer - WH22X35837
- GE Door Lock - WH01X29528
- GE Drain Pump & Filter with Microban for Washers - WH11X29539
- GE Washer Accelerometer - WH03X32138
ШагиSteps
1
Retrieve stored error codes
- Confirm the washer is powered on with no cycle selected and the dial not pressed.
- Press and hold the start pause button about 10 seconds until the lights flash and the display brightens.
- Press start pause repeatedly to scroll through stored error codes for diagnostic clues.
2
Run the forced spin test
- Press start pause to exit error code mode and return to standby.
- Press and hold start pause while rotating the control dial 180 degrees counterclockwise.
- Release the button when the lights flash, then rotate the dial clockwise to mode 14.
- Shut the door, check water and drain connections, and press start pause to initiate spin.
- Observe if the drum spins only four to seven seconds, indicating a failing inverter motor assembly.
3
Prepare the washer for disassembly
- Disconnect power to the washer to ensure safety.
- Gather a 6-in-1 screwdriver, a digital multimeter, a 14 mm socket, a door boot spring tool, and needle nose pliers.
- Tilt or secure the washer as needed to safely access internal components without tipping.
4
Remove the dispenser and console screws
- Pull out the dispenser drawer fully and press the tab on its left side to remove it.
- Locate five screws in the dispenser housing three on the left and two on the right, and remove them with a Phillips driver.
- Lift the console interface up about 15 degrees and pull it forward to unlatch from the bulkhead.
- Remove three screws behind the interface along the top edge of the washer lid.
5
Remove the washer top panel
- Slide the top panel toward you while lifting it up to release it from the washer.
- Set the top panel aside to reveal internal components such as the accelerometer and harness.
6
Inspect the accelerometer and harness
- Locate the accelerometer near the top with a small wire harness attached.
- Ensure the harness is firmly connected and shows no broken or loose wires.
- Replace the accelerometer if error codes persist despite secure connections.
7
Access the door lock and gasket
- Open the washer door and remove two Phillips screws securing the plastic face plate on the right side.
- Remove two more screws securing the door lock and lift it out through the door opening.
- Pry away the door seal retaining wire with a thin screwdriver and roll the gasket off the front lip.
- Disconnect the door lock harness and inspect wires for damage or breaks.
8
Detach the front bulkhead
- Tilt the washer back to remove three bottom screws holding the front panel, then return the washer upright.
- Remove nine top screws from the front panel with two at the corners and seven pointing downward.
- Slide the damper fan assembly rearward if equipped and decouple it from the bulkhead.
- Lift and pull the bulkhead forward to free it from the machine, watching for harness wires on both sides.
9
Check the door harness and counterbalance weight
- Examine both door lock harnesses for bent broken or snapped wires that could cause lock errors.
- Use a 14 mm socket to remove four bolts from the lower concrete counterbalance weight.
- Pull the counterbalance weight off its pegs and set it aside for more access to the drain pump and inverter.
10
Inspect the drain pump if codes suggest drainage issues
- Spin the drain pump impeller by hand and feel for three or four strong points of magnetic resistance.
- Measure about 20 ohms across the pump terminals using a multimeter to confirm functionality.
- Replace the pump if it shows no strong resistance or an open reading on the meter.
11
Remove and replace the inverter board
- Locate the inverter assembly on the lower portion of the machine behind a plastic cover.
- Use a small screwdriver or pliers to release six tabs securing the inverter cover then lift it off.
- Unplug four wire harnesses from the inverter board and free any cable ties or wire trunks.
- Detach two side clips and remove four screws to release the board from the plastic housing.
- Seat the new inverter board in the housing align screws and clips and reattach the wire harnesses.
- Inspect wires for damage around cable ties or connectors before replacing the inverter cover.
12
Reassemble and test the washer
- Guide the inverter board back onto the chassis and secure it with its mounting hardware.
- Reinstall the counterbalance weight with four bolts while holding it in place.
- Position the front bulkhead on its aligning pegs and secure with all top and bottom screws.
- Reconnect the door lock and door gasket then seat the wire retaining spring around the gasket lip.
- Place the top panel reinstall the three lid screws and fasten the console with five dispenser screws.
- Restore power clear error codes in diagnostic mode and run a spin test to confirm the repair.
Clear any stored codes and run a test cycle after repairing the failed component so you can confirm the washer completes spin without stopping mid-cycle. Repair didn't go as planned? Ask our Answers community for help.
«How to Troubleshoot a GE Front Load Washer Stopping Mid Cycle and Not Spinning» — автор Ben Schlichter, iFixit, лицензия CC BY-NC-SA 3.0. Показано без изменений. Открыть оригинал и комментарии →